Supply of Line Pipe and Auxiliary Items

IGI-Poseidon SA

The contract concerns the supply of carbon steel line pipe. The Pipeline route has the following characteristics in relation to line pipe supply:
— Location: Greece, Italy and seabed between,
— Onshore Section, 48” nominal outer diameter, approx. 760 km length,
— Offshore Section Pipeline, 36” nominal outer diameter, approx. 216 km length,
— Offshore Pipeline Design Code: EN 14161 (ISO 13623) plus DNV standards for guidance as required,
— Onshore Pipeline Design Code: EN 1594 and EN ISO 3183 (for line pipe supply).

Προθεσμία

Η προθεσμία παραλαβής των προσφορών ήταν 2018-08-09. Η προμήθεια δημοσιεύθηκε στις 2018-07-04.

Ποιος

• IGI-Poseidon SA

Τι

Πού

• Aνατολική Μακεδονία, Θράκη › Έβρος
• Aνατολική Μακεδονία, Θράκη › Θάσος, Καβάλα
• Ήπειρος › Θεσπρωτία
• Κεντρική Μακεδονία › Θεσσαλονίκη

Ιστορικό προμηθειών

Ημερομηνία	Έγγραφο
2018-07-04	Προκήρυξη σύμβασης
2018-07-27	Συμπληρωματικά στοιχεία

Προκήρυξη σύμβασης (2018-07-04)
Αντικείμενο
Πεδίο εφαρμογής της προμήθειας
Τίτλος: Σωλαγωγοί, σωληνώσεις, σωλήνες, περιβλήματα, σωληνωτά υλικά και συναφή είδη
Ποσότητα ή έκταση:

Line Pipe for Onshore Part (Lots 1 and 2):48" (1219 mm) nominal pipe dia:Approximately 659 km of 18,4 mm wall thickness.Approximately 83 km of 22,0 mm wall thickness.Approximately 34 km of 26,2 mm wall thickness.Approximately 5 km mother pipe for factory hot bends (all above wt’s).Line Pipe and Related Materials for Offshore Part (Lot 3):Pipe Size is 36” with wall thickness from 21,8 to 36,2 mm. Total Length is 224 km.Approx. 110 hot bends from 36” mother pipe, wall thickness 34,4mm are to be supplied.A quantity of anodes and buckle arrestors are to be supplied.Hot Bends for Onshore Pipe 48” (Lot 4):Approx. 270 hot bends from 48” mother pipe and wall thicknesses 18,4 mm, 22 mm and 26,2 mm will be supplied. Mother pipe for the fabrication of the bends will be supplied under Lot 2.918 000 000,00

Συνολική αξία της σύμβασης: 344 000 000,00 💰
Μεταδεδομένα προκήρυξης
Πρωτότυπη γλώσσα: Αγγλικά 🗣️
Τύπος εγγράφου: Προκήρυξη σύμβασης
Φύση της σύμβασης: Προμήθειες
Κανονισμός: Ευρωπαϊκή Ένωση
Κοινό λεξιλόγιο για δημόσιες συμβάσεις (CPV)
Κωδικός: Σωλαγωγοί, σωληνώσεις, σωλήνες, περιβλήματα, σωληνωτά υλικά και συναφή είδη 📦

Διαδικασία
Τύπος διαδικασίας: Διαδικασία με διαπραγμάτευση
Τύπος προσφοράς: Υποβολή για ένα ή περισσότερα τμήματα
Κριτήρια απονομής
Η πλέον συμφέρουσα οικονομικώς προσφορά

Αναθέτουσα αρχή
Ταυτότητα
Χώρα: Ελλάδα 🇬🇷
Τύπος αναθέτουσας αρχής: Άλλη
Όνομα αναθέτουσας αρχής: IGI-Poseidon SA
Ταχυδρομική διεύθυνση: 92 Marinou Antipa Ave, DEPA S.A. Building
Ταχυδρομικός κώδικας: GR 14121
Ταχυδρομική πόλη: Heraklion Attikis
Επικοινωνία
Διεύθυνση διαδικτύου: http://www.igi-poseidon.com 🌏
E-mail: info@igi-poseidon.com 📧
: d.manolis@depa.gr 📧
: g.kostopoulos@depa.gr 📧
: a.fox@depa.gr 📧
: matteo.restelli@edison.it 📧
: marcello.bozzolasco@edison.it 📧
: sabrina.scieghi@edison.it 📧
Τηλέφωνο: +30 2102701050 📞
Φαξ: +30 2102751067 📠

Αναφορά
Ημερομηνίες
Ημερομηνία αποστολής: 2018-07-04 📅
Προθεσμία υποβολής: 2018-08-09 📅
Ημερομηνία δημοσίευσης: 2018-07-06 📅
Αναγνωριστικά
Αριθμός προκήρυξης: 2018/S 128-292946
Τεύχος ΕΕ-S: 128
Πρόσθετες πληροφορίες

1) Candidates shall submit the requested information in -2 originals,- 2 copies and -2 CD’s. One copy to the address in Athens indicated in I.1) (Name, addresses and contact point) and the second to the following address in Milan: IGI-POSEIDON S.A., c/o Edison SpA, Foro Buonaparte 31, 20121 Milan, Italy, FAO: Mrs. Sabrina Scieghi. 2) The overall duration given in II.3) is indicative. A detailed Time Schedule will be provided in the next Tender phase with specific timing required for parts of the supply within the overall duration. 3) The time limit indicated in IV.3.3) of present Notice has to be considered as time limit for submission of requests for any clarification. There is no specification or additional document at this stage. Instructions will be issued to Candidates who are selected to be invited to participate in the Tender.

Αντικείμενο
Πεδίο εφαρμογής της προμήθειας
Σύντομη περιγραφή:

The contract concerns the supply of carbon steel line pipe. The Pipeline route has the following characteristics in relation to line pipe supply:

— Location: Greece, Italy and seabed between,

— Onshore Section, 48” nominal outer diameter, approx. 760 km length,

— Offshore Section Pipeline, 36” nominal outer diameter, approx. 216 km length,

— Offshore Pipeline Design Code: EN 14161 (ISO 13623) plus DNV standards for guidance as required,

— Onshore Pipeline Design Code: EN 1594 and EN ISO 3183 (for line pipe supply).

Αριθμός τμήματος: 1
Τίτλος του τμήματος: Supply of Line Pipe–Onshore
Σύντομη περιγραφή:

The LOT concerns the supply of carbon steel line pipe for the Onshore Pipeline. The Onshore Pipeline has the following characteristics in relation to line pipe…

… supply:— Location: Greece— Section Onshore, 48”nominal outer diameter, approx. 760 km length— Onshore Pipeline Design Code: EN 1594 and EN ISO 3183 (for line pipe supply)— Min design temperature: -20 ºC— Max design temperature: +60 ºC— Design pressure: 100 barg— Pipeline content: Sweet Dry Natural Gas— Line pipe grade: L485ME—— Nominal OD 48-inch with wall thicknesses in the range18,4 mm to 26,2 mmThe line pipe shall be manufactured, pre-qualified and tested in accordance with EN ISO 3183 and Company’s project specifications, which will be issued together with the Invitation to Negotiate.The line pipe shall be supplied coated with an epoxy internal coating and a 3LPE anti- corrosion external coating. The coating application, testing and inspection shall be performed as per EN ISO 21809 and Company’s project specification.

… supply:

— Location: Greece

— Section Onshore, 48”nominal outer diameter, approx. 760 km length

— Onshore Pipeline Design Code: EN 1594 and EN ISO 3183 (for line pipe supply)

— Min design temperature: -20 ºC

— Max design temperature: +60 ºC

— Design pressure: 100 barg

— Pipeline content: Sweet Dry Natural Gas

— Line pipe grade: L485ME

—— Nominal OD 48-inch with wall thicknesses in the range18,4 mm to 26,2 mm

The line pipe shall be manufactured, pre-qualified and tested in accordance with EN ISO 3183 and Company’s project specifications, which will be issued together with the Invitation to Negotiate.

The line pipe shall be supplied coated with an epoxy internal coating and a 3LPE anti- corrosion external coating. The coating application, testing and inspection shall be performed as per EN ISO 21809 and Company’s project specification.

Ποσότητα ή έκταση: L485ME as per EN ISO 3183, SAWL or SAWHOutside Diameter = 48”(1219 mm)Wall Thickness = 18.4 / 22 / 26.2Pipe Lengths = 18 m / 12 mQuantity = 393 km

L485ME as per EN ISO 3183, SAWL or SAWH

Outside Diameter = 48”(1219 mm)

Wall Thickness = 18.4 / 22 / 26.2

Pipe Lengths = 18 m / 12 m

Quantity = 393 km

Συμπληρωματικές πληροφορίες σχετικά με τα τμήματα:

It is the Contracting Entity’s intention that Lot 1 and Lot 2 shall not be awarded to the same…

… Supplier.The Contracting Entity reserves the right to adjust the distribution between Lots 1 and 2 within limits that shall be set out in the Invitation to Tender.

… Supplier.

The Contracting Entity reserves the right to adjust the distribution between Lots 1 and 2 within limits that shall be set out in the Invitation to Tender.

Αριθμός τμήματος: 2
Σύντομη περιγραφή:

The Lot concerns the supply of carbon steel line pipe for the Onshore Pipeline. The Onshore Pipeline has the following characteristics in relation to line pipe…

… supply:— Location: Greece— Section Onshore, 48”nominal outer diameter, approx. 760km length— Onshore Pipeline Design Code: EN 1594 and EN ISO 3183 (for line pipe supply)— Min design temperature: -20 ºC— Max design temperature: +60 ºC— Design pressure: 100 barg— Pipeline content: Sweet Dry Natural Gas— Line pipe grade: L485ME—— Nominal OD 48-inch with wall thicknesses in the range 18,4 mm to 26,2 mmThe line pipe shall be manufactured, pre-qualified and tested in accordance with EN ISO 3183 andCOMPANY’s project specifications, which will be issued together with the Invitation to Negotiate.The line pipe shall be supplied coated with an epoxy internal coating and a 3LPE anti- corrosion external coating. The coating application, testing and inspection shall be performed as per EN ISO 21809 and COMPANY’s project specification.Mother pipe for the fabrication of factory bends is included in the scope of supply.

… supply:

— Section Onshore, 48”nominal outer diameter, approx. 760km length

—— Nominal OD 48-inch with wall thicknesses in the range 18,4 mm to 26,2 mm

The line pipe shall be manufactured, pre-qualified and tested in accordance with EN ISO 3183 and

COMPANY’s project specifications, which will be issued together with the Invitation to Negotiate.

Mother pipe for the fabrication of factory bends is included in the scope of supply.

Ποσότητα ή έκταση: L485ME as per EN ISO 3183, SAWL or SAWHOutside Diameter = 48” (1219 mm)Wall Thickness = 18.4 / 22 / 26.2Pipe Lengths = 18 m / 12 mQuantity = 383 km plus 5km SAWL mother pipe for bends.

Outside Diameter = 48” (1219 mm)

Quantity = 383 km plus 5km SAWL mother pipe for bends.

Αριθμός τμήματος: 3
Τίτλος του τμήματος: Supply of Line Pipe and Auxiliary Items – Offshore Section
Σύντομη περιγραφή:

The Lot concerns the supply of carbon steel line pipe for the Offshore Pipeline. The Offshore Pipeline has the following characteristics in relation to line pipe…

… supply:— Location: Greece, Italy and seabed between— Offshore Section Pipeline, 36”nominal outer diameter, approx. 216km length from Thesprotia, Greece to Italy (including short onshore pipeline sections)— Offshore Pipeline Design Code: EN 14161 (ISO 13623) plus DNV standards for guidance as required.— Max water depth: 1 379 m— Min design temperature: -10 ºC— Max design temperature: 70º C— Design pressure: 170 barg— Pipeline content: Sweet Dry Natural Gas— Linepipe grade: DNV SAWL 485 FDU— Nominal OD 36-inch with a constant ID of 842 mm and wall thicknesses in the range 21,8 mm to 36,2 mm.The line pipe shall be manufactured, pre-qualified and tested in accordance with DNV-OS-F101 and Company’s project specifications, which will be issued together with the Invitation to Negotiate.The line pipe shall be supplied coated with a solvent-free liquid epoxy paint internal coating and a 3LPP anti- corrosion external coating. The coating application, testing and inspection shall be performed as per DNVGL-RP-F106 and Company’s project specifications.Approximately 70 km of line pipe shall be supplied with a concrete weight coating of thicknesses ranging from 50 mm to 120 mm.The concrete coating should either be performed in the Pipe Manufacturer’s facilities, or in other location, or with mobile units close to the delivery port. The Candidate should be responsible to indicate the place, in which the concrete coating will take place, and eventually to deliver the pipe, wherever the Contracting Entity will specify. The line pipe produced shall be compatible for the application of field joint coating and for the installation of sacrificial anode half-shell bracelet cathodic protection. Supply and installation of anodes on the concrete weight coated pipe is included in the scope of supply.Approximately 60 aluminum based half shell bracelet anodes are to be supplied and installed on the concrete weight coated line pipe.Buckle arrestor pipe lengths with wall thicknesses in the range 34,4 mm to 70,4 mm are included in the scope of supply.Induction bends are included in the scope of supply.

… supply:

— Location: Greece, Italy and seabed between

— Offshore Section Pipeline, 36”nominal outer diameter, approx. 216km length from Thesprotia, Greece to Italy (including short onshore pipeline sections)

— Offshore Pipeline Design Code: EN 14161 (ISO 13623) plus DNV standards for guidance as required.

— Max water depth: 1 379 m

— Min design temperature: -10 ºC

— Max design temperature: 70º C

— Design pressure: 170 barg

— Linepipe grade: DNV SAWL 485 FDU

— Nominal OD 36-inch with a constant ID of 842 mm and wall thicknesses in the range 21,8 mm to 36,2 mm.

The line pipe shall be manufactured, pre-qualified and tested in accordance with DNV-OS-F101 and Company’s project specifications, which will be issued together with the Invitation to Negotiate.

The line pipe shall be supplied coated with a solvent-free liquid epoxy paint internal coating and a 3LPP anti- corrosion external coating. The coating application, testing and inspection shall be performed as per DNVGL-RP-F106 and Company’s project specifications.

Approximately 70 km of line pipe shall be supplied with a concrete weight coating of thicknesses ranging from 50 mm to 120 mm.

The concrete coating should either be performed in the Pipe Manufacturer’s facilities, or in other location, or with mobile units close to the delivery port. The Candidate should be responsible to indicate the place, in which the concrete coating will take place, and eventually to deliver the pipe, wherever the Contracting Entity will specify. The line pipe produced shall be compatible for the application of field joint coating and for the installation of sacrificial anode half-shell bracelet cathodic protection. Supply and installation of anodes on the concrete weight coated pipe is included in the scope of supply.

Approximately 60 aluminum based half shell bracelet anodes are to be supplied and installed on the concrete weight coated line pipe.

Buckle arrestor pipe lengths with wall thicknesses in the range 34,4 mm to 70,4 mm are included in the scope of supply.

Induction bends are included in the scope of supply.

Ποσότητα ή έκταση: Approx. 69 km of 21,8 mm wall thicknessApprox. 105 km of 34,4 mm wall thicknessApprox. 50 km of 36,2 mm wall thicknessAn pipe to have Constant Internal Diameter of 842 mm.Approx. 140 Buckle arrestors with wall thicknesses in the range 34,4 mm to 70,4 mm are included in the scope of supply.Approx. 110 hot bends from 36” mother pipe, wall thickness 34,4mm are included in the scope of supply.

Approx. 69 km of 21,8 mm wall thickness

Approx. 105 km of 34,4 mm wall thickness

Approx. 50 km of 36,2 mm wall thickness

An pipe to have Constant Internal Diameter of 842 mm.

Approx. 140 Buckle arrestors with wall thicknesses in the range 34,4 mm to 70,4 mm are included in the scope of supply.

Approx. 110 hot bends from 36” mother pipe, wall thickness 34,4mm are included in the scope of supply.

Αριθμός τμήματος: 4
Τίτλος του τμήματος: Supply of Line Pipe and Auxiliary Items – Factory Hot Bends 48”
Σύντομη περιγραφή:

The Lot concerns the supply of factory hot bends — 48””. Mother pipe for the fabrication of the bends will be supplied under Lot…

… 2.Approx. 270 hot bends with wall thicknesses 18,4 mm, 22 mm and 26,2 mm will be supplied.

… 2.

Approx. 270 hot bends with wall thicknesses 18,4 mm, 22 mm and 26,2 mm will be supplied.

Ποσότητα ή έκταση: Approx. 270 hot bends from 48” mother pipe.

Line Pipe for Onshore Part (Lots 1 and 2):

48" (1219 mm) nominal pipe dia:

Approximately 659 km of 18,4 mm wall thickness.

Approximately 83 km of 22,0 mm wall thickness.

Approximately 34 km of 26,2 mm wall thickness.

Approximately 5 km mother pipe for factory hot bends (all above wt’s).

Line Pipe and Related Materials for Offshore Part (Lot 3):

Pipe Size is 36” with wall thickness from 21,8 to 36,2 mm. Total Length is 224 km.

Approx. 110 hot bends from 36” mother pipe, wall thickness 34,4mm are to be supplied.

A quantity of anodes and buckle arrestors are to be supplied.

Hot Bends for Onshore Pipe 48” (Lot 4):

Approx. 270 hot bends from 48” mother pipe and wall thicknesses 18,4 mm, 22 mm and 26,2 mm will be supplied. Mother pipe for the fabrication of the bends will be supplied under Lot 2.

Διάρκεια: 24 μήνες
Αριθμός αναφοράς: IGI - POSEIDON Tender 08/2018
Τόπος εκτέλεσης
Κύρια τοποθεσία ή τόπος εκτέλεσης:

A port on the north western coast of Greece (e.g. Igoumenitsa) and a port on the north eastern coast of Greece.

Νομικές, οικονομικές, χρηματοπιστωτικές και τεχνικές πληροφορίες
Όροι συμμετοχής
Καταλληλότητα για άσκηση της επαγγελματικής δραστηριότητας:

Candidates are required to submit the following concerning the situation of economic operators: Registration document from an official Professional Institution in compliance with the Law of the country where the base or a legally operating department of the economic operator is established. The document shall declare the capability of the economic operator to undertake relevant supply. In the absence of such document, it will be replaced by a declaration on oath made by the economic operator or in case that such a declaration is not foreseen, declaration in front of judicial or administrative authority, notary public or competent professional body, in the country of origin or registration of the economic operator.

—Company Statutes, according to the legislation of the country where the economic operator is registered.

— Declaration of the Candidate’s decision to participate in the selection to negotiate and appointment of Legal Representative(s) authorized to represent the Candidate. -Declaration of acceptance for the appointment by the Legal Representative of the Candidate.

— Binding statement from all the economic operators that they agree to participate in the selection to negotiate. The statement shall indicate the part of the scope that the economic operator intends to undertake.

– Full contact details of Legal representative.

— Declaration, for each economic operator stating that:

i) It has not been convicted for anything related to its professional integrity and behaviour.

ii) It has not committed a serious professional misdeed. In case that the documents are not prepared in English, they shall be accompanied by official translation in English. The Contracting Entity reserves the right to exclude from invitation to negotiate any Candidate that it reasonably considers has or may have a conflict of interest with the objectives of the Contracting Entity. Economic Operators that are governed by the law of a Third Country (Non Member State) may participate, provided that the EU has signed multilateral or bilateral agreements that assure a corresponding and essential access of Member State undertakings in the markets of the said Third Countries.

Οικονομική και χρηματοοικονομική κατάσταση:

Candidates shall submit declarations for each economic operator that:

i) It is not in a state of bankruptcy, under liquidation, obligatory management, compromise, or any other similar situation resulting from a similar procedure and that no procedure has been instigated against the economic operator for declaration in bankruptcy, obligatory management, compromise or any other similar situation or resulting from any other similar procedure. Candidates shall submit, for each economic operator, declarations that:

i) It has fulfilled its obligations, relating to the payment of Social Security contributions;

ii) It has fulfilled its obligations relating to the payment of taxes, according to the Legislation of the country where it is established. In case that the documents are not prepared in English, they shall be accompanied by official translation in English. Candidates shall submit audited annual accounts for the past 3 years for each economic operator and shall demonstrate financial management capabilities required for funding the supply. Candidates with an average annual turnover of the past 3 years lower than 100 % of the estimated value of the Lots for which they request to participate shall not be invited to tender. In case of Joint Venture or Consortium, the average turnover of the past 3 years for the candidate shall be assessed as the sum of the average annual turnover for each member.

Τεχνική και επαγγελματική ικανότητα:

Candidates are requested to supply track records for line pipe and auxiliary items designed to the applicable standards and within similar

OD and WT range and in similar project conditions. The following information shall be submitted as a minimum:

— Project name, year and location,

— Line pipe grade, OD, WT, and pipeline length,

— Conditions of service (sour / sweet, water depth and lay method for offshore line pipe). Candidates are requested to indicate the following:

— Production capacity for the respective range of pipeline diameters and wall thicknesses,

— Estimated time required to produce the Lot(s) per indicated OD and wall thickness.

Candidates who cannot as a minimum satisfy the following shall be excluded from invitation to negotiate:

(i) demonstrate capability to produce the supply for the OD and WT combinations of one or more Lots;

(ii) suitable certification to ISO9000 or equivalent;

(iii) possession of current licenses for manufacture to the applicable standards.

Candidates who satisfy the above will be further required to prove their capability to produce the supply in accordance with the project specifications which shall be issued together with the Invitation to Negotiate.

Notwithstanding any selection for invitation to tender, the Contracting Entity reserves the right to consider as contract award criteria the detailed capability of the Candidate in relation to the detailed scope.

Εκτέλεση της σύμβασης
Απαιτούμενες καταθέσεις και εγγυήσεις:

At the next stage of this call, the selected candidates will be invited to a tender and submit their bids. After conclusion of the bids evaluation the successful bidder will be required to provide, in accordance with the draft included in the Tender Documents, in Greek or English language:

— a bond equal to 5 % of contract price issued by a bank operating within member states of EU will be asked from the preferred bidder, up to the signature of the contract; and

— a Performance Bond, amounting to 10 % of the total value of the contract, upon signature of the contract and valid until final acceptance of the supply.

Κύριοι όροι χρηματοδότησης και ρυθμίσεις πληρωμών και/ή παραπομπή στις σχετικές διατάξεις που τις διέπουν: Payment Conditions will be set out in the Invitation to Tender documents.
Νομική μορφή που πρέπει να λάβει ο όμιλος οικονομικών φορέων στον οποίο πρόκειται να ανατεθεί η σύμβαση:

Candidates may be either an individual company or a grouping of companies.

If the contract is awarded to a grouping of economic operators, the legal form required by the grouping shall be:

— a Main Supplier to whom the Contract is awarded with named Subsuppliers/Subcontractors for whom the main Supplier is responsible,

— a Joint Venture of economic operators or

— a Consortium of economic operators.

The legal formation will be required prior to any award but is not required for this call for participation or the subsequent negotiation. Candidates shall however be required to demonstrate agreements to legally form any proposed grouping of economic operators, during their submission to this Contact Notice.

Joint Ventures and Consortia shall nominate an economic operator as Leader. A company which participates as a member of the Joint Venture or Consortium of companies shall not participate in the Tender individually.

Reputable, widely recognized and suitably accredited Suppliers are sought.

Άλλοι ιδιαίτεροι όροι:

Draft conditions of the Contract will be set out in the Invitation to Negotiate that will be issued to selected candidates, among them, the Liquidated damages to be applied to delayed deliveries, in respect to the delivery schedule agreed in the contract.

Διαδικασία
Γλώσσες
Γλώσσα: Αγγλικά 🗣️

Αναθέτουσα αρχή
Ταυτότητα
Άλλος τύπος αναθέτουσας αρχής: Other
Επικοινωνία
Πρόσωπο επικοινωνίας: Mr. George Kostopoulos, Technical Director

Αναφορά
Αναγνωριστικά
Αριθμός αναφοράς που έχει αποδοθεί από την αναθέτουσα αρχή: IGI - POSEIDON Tender 08/2018
Πρόσθετες πληροφορίες

2) The overall duration given in II.3) is indicative. A detailed Time Schedule will be provided in the next Tender phase with specific timing required for parts of the supply within the overall duration.

3) The time limit indicated in IV.3.3) of present Notice has to be considered as time limit for submission of requests for any clarification. There is no specification or additional document at this stage. Instructions will be issued to Candidates who are selected to be invited to participate in the Tender.

Συμπληρωματικές πληροφορίες
Σώμα αναθεώρησης
Όνομα: Natural Gas Submarine Interconnector Greece-Italy (IGI Poseidon SA)
Ταχυδρομική διεύθυνση: 92, Marinou Antipa Ave.
Ταχυδρομική πόλη: Heraklion Attikis
Ταχυδρομικός κώδικας: 14121
Χώρα: Ελλάδα 🇬🇷
Τηλέφωνο: +30 2102701050 📞
Διεύθυνση διαδικτύου: http://www.igi-poseidon.com 🌏
Φαξ: +30 2102751067 📠
Υπηρεσία από την οποία μπορούν να ληφθούν πληροφορίες σχετικά με τη διαδικασία επανεξέτασης
Όπως: Σώμα αναθεώρησης
Πηγή: OJS 2018/S 128-292946 (2018-07-04)

Συμπληρωματικά στοιχεία (2018-07-27)
Αντικείμενο
Μεταδεδομένα προκήρυξης
Τύπος εγγράφου: Συμπληρωματικά στοιχεία

Αναφορά
Ημερομηνίες
Ημερομηνία αποστολής: 2018-07-27 📅
Προθεσμία υποβολής: 2018-08-27 📅
Ημερομηνία δημοσίευσης: 2018-07-31 📅
Αναγνωριστικά
Αριθμός προκήρυξης: 2018/S 145-333178
Αναφέρεται στην προκήρυξη: 2018/S 128-292946
Τεύχος ΕΕ-S: 145
Πηγή: OJS 2018/S 145-333178 (2018-07-27)

Νέες προμήθειες σε συναφείς κατηγορίες 🆕

Δομές και υλικά κατασκευαστικών έργων· βοηθήματα κατασκευαστικών έργων (εκτός από ηλεκτρικές συσκευές) (>20 νέες προμήθειες)

Κατασκευαστικά υλικά και παρόμοια είδη (11)

Σωλαγωγοί, σωληνώσεις, σωλήνες, περιβλήματα, σωληνωτά υλικά και συναφή είδη (2)